$9.73
On Hold
REDCON 2.4G 6CH Microlite DSM2 Full-Range Receiver CM621
More than 10 available
Details
Shipping: Australia: $7.00 (more destinations)
Condition: Brand new
*The store has not been updated recently. You may want to contact the merchant to confirm the availability of the product.
REDCON 2.4G 6CH Microlite DSM2 Full-Range Receiver CM621
Great little Receiver ! ! Light weight with long range ability ! And Priced cheap !
Brief Description:
Product Brand : REDCON
Product Name: CM621 receiver
Band: 2.4GHz
Channel: 6
Modulation: DSM2
Dimensions (W x Lx H): 19 x40x9mm
Weight: 4.4g
Voltage Range: 4-10v
Brown-Out Voltage: 4.0v (Always supply power above this voltage)
Antenna Length Main RX: 30mm
Approx. Range: 400m (tested with JR DSX9)
Compatibility (Spektrum and JR DSM2): DX6I,DX7,DX8 DSX7,DSX9 DSX11
Note:
This receiver may not be compatible with EU market Spektrum transmitters (which doesn't support DSM2).
;Features:
Patent pending Model Match prevents flying a model using the wrong model memory (feature will not work with module systems).
Servo Sync (feature will not work with module systems)
Preset fail safe system.
Quick Connect
Horizontal-Pin configuration
Red LED indicates number of hold
Binding Procedure:
1. Put the binding harness into connector location marked BIND. Next apply power to the receiver. Receiver LED should illuminate it means bind is accomplished
2. To set fail-safe throttle and control surface positions, (minimum throttle and all control surfaces set to neutral is suggested). Press and hold the bind button of transmitter (LED will illuminate), Turn on the transmitter.
3. Receiver LED will change from rapid flashing to slow flashing and a few seconds later when bind is accomplished the LED of receiver will illuminate solid. All fail-safes should be programmed correctly now.
4. Remove binding harness from the BIND channel. Restart the receiver by cycling it power off and turn on and connect battery into BIND channel is recommended. All channels should function properly now.
You can test fail-safe by holding sticks in corners, cycle transmitter on and off. Surfaces and throttle should return to your preset fail-safe positions.
Wireless Simulator Interface:
- Main receiver and satellite must connect.
- Receiver must bind with transmitter first (AUX4 channel do not plug binding harness)
- AUX3 is the (W.D.S.C) channel, connect with simulator line
- BIND channel and AUX4 channel plug the binding harness
- Apply power to the receiver with USD line or battery
- Turn transmitter on, now both LEDS keep light and simulator works.
LED Indication:
- Solid illuminated Red LED is indicates good signal. If flashing, 1 flash indicates 1 signal loss, 2 = 2 signal losses and etc....
- The Orange LED on main receiver should flash one time when power is first applied. It will flash several times when binding harness is connected.
Priority Direct Mail 6-9 business U.S. , U.K. ,Australia and most other most destinations.Up to 6 ship for same rate !
Can Ship free with other products.
Package Includes:
1 REDCON CM621 Receiver
1 Bind plug
Great little Receiver ! ! Light weight with long range ability ! And Priced cheap !
Brief Description:
Product Brand : REDCON
Product Name: CM621 receiver
Band: 2.4GHz
Channel: 6
Modulation: DSM2
Dimensions (W x Lx H): 19 x40x9mm
Weight: 4.4g
Voltage Range: 4-10v
Brown-Out Voltage: 4.0v (Always supply power above this voltage)
Antenna Length Main RX: 30mm
Approx. Range: 400m (tested with JR DSX9)
Compatibility (Spektrum and JR DSM2): DX6I,DX7,DX8 DSX7,DSX9 DSX11
Note:
This receiver may not be compatible with EU market Spektrum transmitters (which doesn't support DSM2).
;Features:
Patent pending Model Match prevents flying a model using the wrong model memory (feature will not work with module systems).
Servo Sync (feature will not work with module systems)
Preset fail safe system.
Quick Connect
Horizontal-Pin configuration
Red LED indicates number of hold
Binding Procedure:
1. Put the binding harness into connector location marked BIND. Next apply power to the receiver. Receiver LED should illuminate it means bind is accomplished
2. To set fail-safe throttle and control surface positions, (minimum throttle and all control surfaces set to neutral is suggested). Press and hold the bind button of transmitter (LED will illuminate), Turn on the transmitter.
3. Receiver LED will change from rapid flashing to slow flashing and a few seconds later when bind is accomplished the LED of receiver will illuminate solid. All fail-safes should be programmed correctly now.
4. Remove binding harness from the BIND channel. Restart the receiver by cycling it power off and turn on and connect battery into BIND channel is recommended. All channels should function properly now.
You can test fail-safe by holding sticks in corners, cycle transmitter on and off. Surfaces and throttle should return to your preset fail-safe positions.
Wireless Simulator Interface:
- Main receiver and satellite must connect.
- Receiver must bind with transmitter first (AUX4 channel do not plug binding harness)
- AUX3 is the (W.D.S.C) channel, connect with simulator line
- BIND channel and AUX4 channel plug the binding harness
- Apply power to the receiver with USD line or battery
- Turn transmitter on, now both LEDS keep light and simulator works.
LED Indication:
- Solid illuminated Red LED is indicates good signal. If flashing, 1 flash indicates 1 signal loss, 2 = 2 signal losses and etc....
- The Orange LED on main receiver should flash one time when power is first applied. It will flash several times when binding harness is connected.
Priority Direct Mail 6-9 business U.S. , U.K. ,Australia and most other most destinations.Up to 6 ship for same rate !
Can Ship free with other products.
Package Includes:
1 REDCON CM621 Receiver
1 Bind plug
